Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain, durable and long-lasting. As opposed to aluminium and timber they are not susceptible to corrosion or rot.

It is important to clean and oil upvc window repair doors and windows on a regular basis. This will help prevent costly repairs and improve energy efficiency.

1. Broken Glass

If the glass in your window is broken it could cause a large deal of damage to your home, which can make it extremely dangerous and possibly fatal. You should take the time to ensure that your windows are in good condition.

Single-pane windows are relatively simple to replace and will usually fit into the frames that were previously in use very easily. However when you have double pane windows that are secured by internal beading, it'll be more difficult to take out the panes that are in place and replace them with new ones. In this case, it is necessary to buy plastic spacers to aid in fitting the new pane into the window frame.

If you're planning to try to remove the glass panes yourself, it is essential to wear the proper safety gear that includes gloves with a thick layer of material and protective eyewear. You should also lay down a dropcloth prior to you begin working on the window panes to ensure that any shards of glass fall onto the fabric, not onto the floor and could be trampled under.

Once the glass is removed from the window, it's best to seal the gap with packaging tape or duct tape to block drafts and water from entering the home until a professional is able to come out and repair the window. This will also act as a barrier, preventing any intruders to gain access into your home. If the gap is particularly large, you may want to consider using an alarm door that comes with an integrated window as it will provide the best of both worlds.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash windows. However, with time, they may be afflicted by a variety of issues, including sliding. A sagging window can cause problems with light, draughts and even security. It's crucial to act when you notice your uPVC windows are falling down.

Repositioning the hinges can help fix a window that is sliding. You'll first need to open the windows so you can get at the frame. After that, using an screwdriver, unscrew the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and verify the an appropriate fit. If you're happy with the fit, tighten the screws to ensure that they stay in place.

If you are unable to reposition the hinges, you may need to replace the seal. Seals made of rubber can dry out and lose their elasticity with time, leading them to loose their elasticity. It is important to replace your seal as quickly as you can to ensure that your uPVC window waterproof and draughtproof.

UPVC handles can also loosen up. Often it is due to screws that have become loose over time. However, it could also happen because the handle mechanism has been worn out. Fortunately, it's easy to repair the handle of a window that is loose yourself. You'll first need to close the window and do an experiment fitting. The corners of the sash need to be aligned with the casing joint. If it doesn't, you can use a screwdriver to loosen the handle and return the mechanism to its original its original position.

3. Water Leaks

If you're waking up to wet floors and mouldy walls each time it rains it is important that you take action. The leaks of water from windows do not only lead to the degradation of your home's structure but also hamper your efforts to regulate the temperature inside your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a relatively easy fix that can be done by any DIY expert. Depending on the severity of the issue is, the old caulking might need to be removed. When it is time to uPVC repair, broken it is important to avoid over-caulking. This will make your window more difficult to clean and lower its energy efficiency.

It is important to check that the drainage holes are clear of debris and that the sill pan is angled properly so that it drains away from the window. In more serious cases you might have to consider replacing the window.

Other signs of long-term water leakage are decayed sills and the appearance of black spots of mold on the walls near the window. This fungus thrives under conditions of dampness and can spread quickly throughout the home.

It is also important to remember that if the leakage is coming from between the glass in your double glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or broken sliding. A uPVC specialist can easily solve this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open in a breeze It could be the hinges that are at fault. These are easily replaced by any competent DIYer and are usually completed in just a few minutes.

Like any mechanical part, hinges can be damaged over time. The process of replacing a hinge on a window is an easy procedure, but it is easier if you have someone to help hold the frame up.

Check that the uPVC hinges open and close in the proper direction. You can do this by looking for the arrows on each hinge. This shows which way the window should open.

The issue could be caused due to opening the window in the wrong way or by a poor installation at the factory. It is usually possible to fix the issue by sending us a photo on our website. We will be happy to give you suggestions.

Regularly lubricating hinges is also essential. This can be accomplished by applying a light engineering oil to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window to operate and close more easily. It can also prevent corrosion and reduce the risk of sticking. Ideally, you should perform this every year. WD40 and other solvent based fluids are not recommended since they can damage the parts of your uPVC window.

5. Draughts

Draughts in upvc windows can be caused by a variety of various factors. The hinges can also be misaligned due to wear, which can cause an opening where the sash and frame meet. If they are beyond repair, it could be necessary to have them realigned. In addition, the interlock could be unbalanced. This is located on the hinge side and may need to be cleaned. In some instances it might be necessary to replace the hinges.

The next common reason for draughts is window seals. They are prone to wear or damaged over time and will allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity glasses. This will help control indoor temperatures, and reduce the risk of draughts.

Another, and most effective methods to reduce the draughts in your home is to use a draught excluder. These are typically fabric tubes that are filled with some kind of filler. They can be positioned on top of your windowsill. They can help block out cold air and keep your home warm and cosy!

Your windows made of upvc will keep providing excellent insulation and security for your home by performing regular maintenance and repairs. It is essential to remember that all windows eventually wear out and it could be more cost-effective to replace them instead of fixing them. If you encounter any issues with your upvc window it is recommended to speak with an expert immediately.