Reasons Your fiat 500 keys 500 Key Fob Won't Work

A fiat 124 spider key fob cover 500 key fob is a handy way to open the doors and start the car. However, there are many reasons why the key fob might stop functioning. It could be due to a dead battery or damaged receiver module, water damage problems, and interference.

This listing is for a NEW replacement Fiat Flip Key Remote - an exact replica of the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not functioning. Modern key fobs have a limited range of operation, and must be within some feet of the vehicle to operate. If you are not within your car and press the keyfob button, it will not respond and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) with a new battery from a reputable brand such as Panasonic Duracell or Energizer. You can typically find them at your local hardware store or on the internet.

After you've changed the battery on the coin cell You can test it by standing near your fiat key fob replacement 500 and pressing the buttons. The parking lights should light up and the key fob should operate the lock and unlock switch.

If the key fob doesn't work after replacing the battery, it may have water damage that stops it from communicating with the receiver module inside your car. Water damage can occur in many ways, including simply splashing or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If this isn't working, you'll have to get your fob reprogrammed either by an auto locksmith or dealer.

Water Damage

Water damage can happen if you immerse the fob in the ocean, or wash it in a washing machine. Saltwater can be particularly harmful to the circuit board of the fob and can cause it to short out and eventually die. The fob getting wet is not an ideal choice however, if you drop it into an empty cup of water, or do not remember to remove it from your pocket before you run the washer do not give up hope.

Remove the battery first. Before replacing the battery, clean the electronic chip using isopropyl or a similar product. Next test the fob to check if it functions. If the key does not function then it might need to be reprogrammed. This is typically handled by a professional or dealer auto locksmith.

If the key is older and has not been programmed to your car it is likely to need to be replaced completely. A professional locksmith for cars can do this job. The locksmith must cut the key to match the ignition in your vehicle. They will also need to reprogram the fob for the car's system. This is a fast and cost-effective procedure that can be completed within the next day.

Receiver Module Issues

One of the main reasons why your 500 key fob might stop working is that it's simply out of range. The remote has a range of 30 feet. Therefore, should you be too far from your vehicle it won't respond to your commands. It is possible to fix this by moving the remote closer to your car until it responds.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and the fob isn't working, it could have an internal circuit board problem. In most cases, reprogramming the fob can resolve the problem. You can find the instructions for most vehicles on YouTube or in the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they loose tension, it can prevent your coin battery from being properly seated and cause your remote to malfunction.

In rare instances the fob might become disconnected from your vehicle because of software or hardware issues. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases they may have to reinstall the program in your body control module, too.

Interference

Interference can also cause the key fob to not be able to receive or transmit signals. This may happen if the key fob is in close proximity to a radio transmitter, like a cell phone or radar detector. The key fob may not work because of a weak connection with the buttons, water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to fix it (e.g. You may have a faulty 500 receiver module after you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module is situated under the dash, Fiat 124 Spider Key Fob Cover and it picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands which are then processed by the vehicle.

There is a simple way to reset the 500's in-board system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Reconnect the battery. This will remove any remaining electrical charge and restart the car's computers. This could help the key fob to function again. If the issue persists, you should consult an expert technician. They will be able to determine the root of any issues.